• Pre-calibrated for accuracy
• Made of durable, ABS (telephone type) plastic
• USDA approved
• Large capacity canister with cone-shaped top
• No need for a striking stick
• Satisfaction guaranteed

Why pay hundreds of dollars for a test weight scale when the patented, made in USA, Acu-Test Scale can do the same job at a fraction of the cost? With nearly 60,000 units sold around the world, this popular and economical scale has proven that it can provide you with years of dependable service.

The Acu-Test, designed by a Minnesota farmer, makes it simple for you to determine yield, capacities and feed quality. Its easy-to-read level vial helps you measure all varieties of grain including corn, soybeans, oats and wheat. Carry it along in your combine to instantly determine yield of different varieties. Keep it handy in your truck when delivering grain to the elevator or dryer to verify measurement. It's also a valuable tool for the grain trucker when loading on the farm.

Also available is a Fertilizer Density Scale which measures pounds per cubic foot!

• One person operation - no help needed
• Self-adjusting-fits all drums up to 55 gallons
• Lifts all barrels with a lip or snap ring
• Even lifts open and damaged barrels
• Satisfaction Guaranteed

You've suffered enough with heavy and unwieldy barrels. The Bold Eagle Barrel Harness eliminates strained backs, smashed fingers and toes, hernias, pulled muscles, damaged barrels, and spilled contents. This easy to install (10 seconds or less) harness picks up barrels vertically. It can be used on conventional, plastic, fiberandsnap ring drums. And used with cranes and overhead joists.

"Why didn't we think of this?!? Ever rolled a barrel off the bed of your truck on to a tire and then tried to tip it back up right! Anyone's back is worth this low  price".

Messing with hard-to-reach-and-pull bearings has always been a major annoyance. Say goodbye to time-and-money wasting bearing problems with a Lewis 2-way Flange Bearing Puller. This clever device removes the Cam Lock Flange and eccentric bearings. Made in the USA, the rugged puller has a lifetime guarantee against defective workmanship and material.

The LBP- 1 model is 71/4" long, 2 1/4" round in diameter and weighs about 61/2 lbs. It has a ??" x 10", long draw bolt inserted into the end of the puller nut. The main puller housing will pull shaft sizes 1 1/16",1 1/8", 1 3/16" and 1 1/4". A small collet that inserts into the main puller housing will pull 13/16", 7/8", 15/16" and 1".

The LBP-2 model is 7??" long, 3" round in diameter and weighs about 10 lbs., also using the ??" x 10" long draw bolt. The main puller housing will pull industrial shaft sizes 1 9/16", 1 1/2" and 1 7/16". The small collet will pull l 3/8", 1 5/16", and 1 1/4". All components have been through a hardening process to increase strength and durability

Extensions: 7 inch cold-rolled steel extensions, exclusively designed to fit the Lewis 2-way Flange Bearing Puller, are also available. The Extensions simply fit between the main puller and the cap nut. You can add as few or as many as you need to fit the length of your shaft.

MODEL LBP-1 PULLER
MODEL LBP-2 PULLER

EXTENSIONS FOR THE LBP-1
EXTENSIONS FOR THE LBP-2

• Stands 14" tall-twice as high as most others
  
• Provides twice the typical area for water to enter
  
• Made form tough, long-lasting steel
  
• Dipped in safety orange paint with a bright flag protruding from the top for high visibility
  
• Bars are tightly spaced to keep out small animals
  
• Fits inlets up to 10 inches (larger sizes available)

A plugged tile can be expensive. It can be costly just determining where it's plugged. And if it's a wet year, there's going to be crop loss. You can't afford that. The best investment you can make in protecting your tile is a good BEEHIVE. Many don't provide the protection you need or they're difficult to see and easy to run over. That's why we strongly recommend you consider our durable and bright BEEHIVES.

CHEAP PROTECTION
PRICE $36.99

No more guessing during night-time operation or dusty conditions. This innovative new Cutting Height Gauge gives you excellent visibility A convenient, easy-to-view, numbered scale shows cutting height from 4" to 20''. This durable gauge comes fully assembled and ready for immediate installation.

It's easily adaptable to fit all makes of combines including John Deere, Case IH, Massey Ferguson, White, New Holland, Gleaner and newer model Hesston S.P. Swathers.